Help Center1. Fill out the placement information in the Placement section.
a. Scroll down to the Placement section.
b. Enter the Required Thickness (Inches) in the corresponding text box.
c. Select your contractor.
i. Click the Search button to open a pop-up window with a list of all the contractors on your project.
1. Select the contractor you are working with.
2. Click Accept.
d. Enter any notes in the Notes text box.
e. Select if the steel verification passed, failed, or is not applicable using the Pass, Fail, and N/A buttons, if applicable.
i. If the steel verification passed or failed, enter any required information in the Steel Notes text box.
f. Enter the cure gallons and cure square feet in the Cure Gallons and Cure SQFT text boxes, if applicable.
i. After entering this information, the Cure Value will populate. Compare the Cure Value against the Cure Rate.
ii. Select whether Adequate Coverage was reached using the Yes/No buttons.
g. Repeat steps a–f as needed for additional Placement sections.
2. Fill out the core information in the Cores section.
a. Select the Cores drop-down at the bottom of the Placement section. This will open the Cores section within the Placement section.
b. Verify the Measurement Date is correct.
c. Enter the Required Thickness (in) in the corresponding text box.
d. Enter the measured thickness in the Thickness 1, 2, and 3 text boxes. Once those values are entered, the Avg. Measured Thickness (in) and the Difference (in) values will populate.
e. Enter any notes in the Notes text box.
f. Repeat steps a–e as needed for additional Core sections.
3. Fill out the test information in the Test section.
a. Enter the cylinder number in the Cylinder # text box, if applicable.
b. Click the Add Strength button, if applicable.
i. Select your break days using the Break Days selector.
ii. Verify that the correct technician is loaded in the Technician drop-down.
c. Verify that the Date and Time in the Time Sampled section are correct for the date and time the tests were taken.
Note: If you click the Now button to the right of the Time selector, it will auto-populate the Date and Time selectors with the current date and time.
d. Verify that the Equipment Settings section has the correct equipment settings.
e. Click the Set Location button in the Sample Locations section, if applicable. This will take you to the Set Location map page.
i. Select the placement you want to add your sample location to.
ii. Click the Add Location button in the top left corner.
iii. Select the points on the placement where you want your sample locations to be marked.
iv. Repeat steps i–iii as needed.
f. Select whether water was added using the Yes/No buttons, if applicable.
g. Select whether air was added using the Yes/No buttons, if applicable.
h. Enter the air percentage in the % Air text box, if applicable.
i. Enter the air temperature in the Air Temp text box, if applicable.
j. Enter the concrete temperature in the Concrete Temp text box, if applicable.
k. Enter the slump in the Slump text box, if applicable.
l. Enter the unit weight in the Unit Weight text box, if applicable.
m. Enter the batch time in the Batch Time selector, if applicable.
n. Verify that the correct technician is loaded in the Technician drop-down for each of the applicable Readings sections.
o. Select whether this report was an Independent Assurance report using the IA Sample Yes/No buttons.
i. Enter who you performed the IA with in the IA With text box.
ii. Enter the Connected Report ID in the Connected Report ID text box.
p. Enter any notes in the Notes text box.
q. Repeat steps a–p as needed for additional test sets.
4. Prepare and generate the Break Sheet and Core Sheet printable reports.
a. Back out of the report and perform an internal sync.
b. Re-enter the report and click the Print Break Sheets and Print Core Sheets buttons in the bottom right of the Test Set Info sections.
c. After you have clicked those two buttons, a file/email will open containing a PDF report of the Break Sheet and Core Sheet.
5. Submit your report.
a. Submit your report by clicking the Close button in the bottom right of the Test Set Info section.
Note: If there are any errors with your report, a pop-up will appear when you attempt to close the report that will log the issues with the report. There are two ways to resolve this:
i. Using the information provided, go through and either fix or enter the data required.
ii. There will be two or more override text boxes that appear. In the override text boxes, fill out your reasons for submitting your report with errors, and then close your report as shown in Step 5.